Fimaks – Maize Choppers

MC10X MAIZE CHOPPER SINGLE ROW(V-BELT DRIVEN)

The MC10X Maize Chopper is a result of many years of experience in the harvesting of silage maize. It is known for its high quality and convenient price.

To get the best result from silage the maize harvester has to chop stems and cobs perfectly. Maize harvester’s feeding system is designed to feed the flywheel at right angles for the best quality silage. The flywheel is equipped with 10 specially hardened knives revolving at nearly 1600 rpm. There are two feeder drums and two pressure rollers that control the feeding of the maize to the flywheel. One of the pressure rollers is spring loaded and toothed; the other one is not. The pressure rollers are vertically mounted right behind the feeder drums so that stems and cobs are always chopped at right angles. This is the secret of the machine’s low power requirement and short length of chop.

For the protection of the feeding system an easily accessible shear bolt is mounted on the machine. It protects the feeding system against the intake of earth and stones in bad conditions.

While in operation, height adjustable wheel maintain an even working height thus preventing the intake of earth and stones in bad conditions.

The MC10X is driven by a pto shaft with an overrun clutch and through maintenance free V-belts. A manual V-belt tightener is mounted on the machine. The feed unit is powered by a transmission running in an enclosed grease bath; totally maintenance free.

Knife grinding is easily carried out with the built-in sharpening device.
The chute is rotated by a hydraulic cylinder. A manual remote control adjusts the deflector. Both controls can be adjusted from the driver’s seat.

The height of the machine can be reduced by folding down the upper part of the chute.

VIDEOS

CHARACTERISTICS            MC10X                        
Number of Rows 1
Length (m) 2,10
Height (m) 3,25
Width (m) 2,30
Height Chute Folded Down (m) 2,20
Weight (kg) 575
Number of Knives 10
Number of Blowers 5
Tyre 16,5 X 6,5-8 6PR
3pt. Hitch Cat. II
PTO (rpm) 540
Minimum Power Requirement (kW/hp) 32 / 45
Maximum Permissible Power (kW/hp) 88 / 120
Chopping Length 4,5 – 6 – 10 – 15 mm.
Capacity 49 tons/hour

MS12SL MAIZE CHOPPER SINGLE ROW(GEARBOX DRIVEN)

The MS12SL Maize Chopper is an ideal machine for small farms. The machine is connected to tractor by 3pt. hitch and the weight of the machine is supported by the support tyre.

Drivetrain is made of a gearbox and pto shaft. The feeding unit consist of 2 feeding drums which cut the plant also. The cutting knives located on the drums provide a clean cut for the plant. Also there is a safety mechanism for excessive load.

The feeding system is driven by a closed maintenance free gearbox. The chopping unit is made of 12 knives in order to provide a cutting length of min 5mm.

While in operation, height adjustable wheel maintain an even working height thus preventing the intake of earth and stones in bad conditions.

Knife grinding is easily carried out with the built-in sharpening device.

The chute and deflector is rotated by a hydraulic cylinder. The pressure for hydraulic cylinders is provided through the pump located on the machine.

The height of the machine can be reduced by folding down the upper part of the chute.

The MS12SL Maize Chopper is an ideal machine for small farms. The machine is connected to tractor by 3pt. hitch and the weight of the machine is supported by the support tyre.

Drivetrain is made of a gearbox and pto shaft. The feeding unit consist of 2 feeding drums which cut the plant also. The cutting knives located on the drums provide a clean cut for the plant. Also there is a safety mechanism for excessive load.

The feeding system is driven by a closed maintenance free gearbox. The chopping unit is made of 12 knives in order to provide a cutting length of min 5mm.

While in operation, height adjustable wheel maintain an even working height thus preventing the intake of earth and stones in bad conditions.

Knife grinding is easily carried out with the built-in sharpening device.

The chute and deflector is rotated by a hydraulic cylinder. The pressure for hydraulic cylinders is provided through the pump located on the machine.

The height of the machine can be reduced by folding down the upper part of the chute.

CHARACTERISTICS      MS12SL                      
Number of Rows 1
Length (m) 2,30
Height (m) 3,10
Width (m) 2,40
Height Chute Folded Down (m) 2,20
Weight (kg) 540
Tyres 16,5 X 6,5-8 6PR
3pt. Hitch Cat. II
PTO (rpm) 540
Needed Power (kW/hp) 32 / 45
Chopping Length 5 mm.
Capacity 35 tons/hour

 

BIGDRUM 1250 ROW INDEPENDENT MAIZE CHOPPER (1,25 M.)

The Row Independent Maize Chopper has a working width of 1,25m. and with its cutter and feeder drum it can chop two rows of maize at one pass. One of the most important specification of the machine is its foldable chassis. The chassis can be folded so that the machine stays behind of the tractor. By driving backwards the machine can open a way in the middle of the field in order to decrease the number of turns on the field and decrease the fuel consumption of tractor.

The cutter and feeder drum carries the maize to the feeding unit. Row independent maize chopper’s feeding system is designed to feed the flywheel at right angles for the best quality silage. The flywheel is equipped with 12 special hardened knives revolving at nearly 1400 rpm. There are two feeder drums and two pressure rollers that control the feeding of the maize to the flywheel. One of the pressure rollers is spring loaded and toothed, while the other one is not. The pressure rollers are vertically mounted right behind the feeder drums so that stems and cobs are always chopped at right angle. This is the secret of the machine’s low power requirement and short length of chop.
For the protection of the feeding system an easily accessible shear bolt is mounted on the machine. It protects the feeding system against the intake of earth and stones in bad conditions.

While in operation, height adjustable wheel maintain an even working height thus preventing the intake of earth and stones in bad conditions.

The chute system of the machine is easily controlled hydraulically by the tractor. The chute has enough length and height to reach the trailer in front while driving backwards. Also it has an optional extension accessory for loading trucks and high trailers.

Knife grinding is easily carried out with the built-in sharpening device.
The height of the machine can be reduced by folding down the upper part of the chute.

CHARACTERISTICS BIGDRUM 1250           
Number of Rows 2
Length (m) 3,05
Height (m) 3,96
Width (m) 3,30
Chute Folded Height (m) 2,20
Weight (kg) 1350
Number of Knives 12
Number of Blowers 12
Tyre 165 / 80 R13
3 Point Hitch Cat.II
PTO(rpm) 1000(540 optional)
Minimum Power (kW/hp) 64 / 90
Cutting Length 4,5 – 6 – 10 – 15 mm.
Capacity 49 tones/hour

BIGDRUM 2200 ROW INDEPENDENT MAIZE CHOPPER (2,20 M.)

The Row Independent Chopper has a working width of 2,2m. and with its cutter and feeder drums it can chop 3 rows of maize at one pass. The machine can be operated both at front hitch or back hitch of the tractor.

The cutter and feeder drum carries the maize to the feeding unit. Row independent chopper’s feeding system is designed to feed the flywheel at right angles for the best quality silage. The flywheel is equipped with 12 special hardened knives revolving at nearly 1200 rpm. There are two feeder drums and two pressure rollers that control the feeding of the maize to the flywheel. One of the pressure rollers is spring loaded and toothed, while the other one is not. The pressure rollers are horizontally mounted right behind the feeder drums so that stems and cobs are always chopped at right angle. This is the secret of the machine’s low power requirement and short length of chop.

The functions of the machine can be controlled from the tractor cab by a wired remote control unit. The angle of drums, lifting and rotation of the chute, adjustment of deflector and the lifting of leaned plants is controlled through this controller.

Knife grinding is easily carried out with the built-in sharpening device. The lightining is provided as standard equipment for working at night.

CHARACTERISTICS BIGDRUM 2200        
Number of Rows 3
Length (m) 2,80
Height (m) 4,20
Width (m) 2,40
Weight (kg) 2000
Number of Knives 12
Tyres 2×185/80 R14
3pt. Hitch Cat. II – III
PTO (rpm) 1000
Minimum Needed Power 115 kW ( 150 hp )
Chopping Length 4,5 mm.
Capacity (acre/hour) 8